![]() ![]() Plug your new LG dryer into the outlet and you are all ready to go. We had our LG Adapt-Able stacking W/D delivered, and to our dismay, the dryer cord is too short to reach down to where the plug is. Match the other colored wires to their coordinating terminal blocks and screw each wire on tightly with no gap or slack.įinally, screw the green screw back on the mount and screw the access cover back into place. Place your white ground wire and your white neutral wire to the center terminal block and securely screw into place. Remove the bottom row of screws for each block.Īlso remove the green ground screw, which is holding in place the white neutral wire. You will notice a black, white and red wire connected to the terminal block and a white ground wire connected on the green screw mount. Install a UL listed strain relief into the power cord through hole and then thread the four wire power cord through the strain relief.Ī cord strain relief is required to prevent accidental pull from the unit. Remove the screws holding the terminal block access cover and pull off the access cover. During installation, you can also refer to the installation diagram provided for you located near the terminal. If you are using a 3-wire power cord, follow the steps below to connect your cord. Electric dryers run on 220 volts and use either the three-prong NEMA 11-30 or the four-prong NEMA 14-30 plug depending on age. LG makes it easy to properly install and setup your new electric dryer. It has one hot terminal, one neutral and a ground and plugs into a standard three-prong, 110-volt receptacle. Attach the hot water line to the hot water tap and the cold water line to the cold water tap. Tighten the fittings so that they are secure. Attach the hot water line to the red hot water inlet on the back of the washer and the cold water line to the blue cold water inlet. To be safe, make sure that the cord is not plugged in and turn the breaker off that connects to your laundry outlet. A typical gas dryer comes with a standard three-prong NEMA 5-20 plug. Insert a rubber seal into the threaded fitting on each hose. Place the unit where it is to be installed, leaving the back exposed. This video will take you through the step by step process so you can start using the many features your LG dryer has to offer. LG makes it easy to properly install and set up your new electric dryer. Plug your new LG dryer into the outlet and you are all ready to go.4-Wire Power Cord Installation Match the other colored wires to their coordinating terminal blocks and screw each wire on tightly with no gap or slack. The new dryer has a 4 prong plug and the outlet. Remove the bottom row of screws for each block, but leave the green ground screw and wire in place. The new homeowner is bewildered when the dryer plug doesnt match the outlet. ![]() Cheaper than the LG DLEX9000V electric dryer by at. 1 spot in our rating of the Best Dryers of 2023 with a score of 4.3 out of 5. Install a drain relief into the power cord through hole and then thread the three wire power cord through the strain relief.Ī cord strain relief is required to prevent accidental pull from the unit. The Electrolux 8-Cubic-Foot EFME627U Electric Dryer earns the No. 9-Cycle Electric Dryer with Sensor Dry - White, Model DLE7300WE has its own terminal block that must be connected to a separate 240 VAC, 60-hertz, single. Remove the screws holding the terminal block access cover and pull off the access cover. Unlike Gas Dryers that come with a power attached, Electric Dryers do not come with an attached power cord. Whether you choose to add professional installation to your new dryer purchase or install it yourself, you must purchase a power cord appropriate for your outlet. 4-prong plugs are used for homes built after the year 2000. ![]() Opt for a magnetic screwdriver to keep hold of the screws and help prevent the risk of dropping them in the back of the dryer. 3-prong plugs are used for homes built before the year 2000. The plate will likely be above the power cord in the back of the appliance. To be safe, make sure that the cord is not plugged in and turn the breaker off that connects to your laundry outlet. Using a screwdriver, remove the plate housing the electrical wires. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |